Build errors when using Erika3

Forum related to ERIKA Enterprise and RT-Druid version 3

Moderator: paolo.gai

Post Reply
Junjie
Newbie
Posts: 6
Joined: Wed Mar 07, 2018 4:00 pm

Build errors when using Erika3

Post by Junjie » Wed Mar 07, 2018 5:26 pm

Hi,

My name is Junjie Shi, I am a PhD student from TU Dortmund.
Recently, I am using the new release of ERIKA V3 on windows 10-64 bit.
After installing all the needed software following the "quick start", I am unable to build the project, the error messages are shown as follows:

15:51:34 **** Incremental Build of configuration Default for project fachproject ****
make all
make[1]: Entering directory '/cygdrive/c/Users/JUNJIE~1/WORKSP~1/FACHPR~1/erika'
ERIKA_FILES=/cygdrive/c/Users/JUNJIE~1/DOCUME~1/ARDUIN~1/ECLIPS~1/eclipse/plugins/COMEUE~1.201/ee_files
make[2]: Entering directory '/cygdrive/c/Users/JUNJIE~1/WORKSP~1/FACHPR~1/erika/doc'
************************************************
* Erika Enterprise Documentation Generation... *
************************************************
**********************************************************
* Erika Enterprise Documentation Generated successfully! *
**********************************************************
make[2]: Leaving directory '/cygdrive/c/Users/JUNJIE~1/WORKSP~1/FACHPR~1/erika/doc'
make[2]: Entering directory '/cygdrive/c/Users/JUNJIE~1/WORKSP~1/FACHPR~1/erika'
***************************************
* Erika Enterprise Libraries build... *
***************************************
CC hooks.c
/bin/sh: C:\PROGRA~1\cygwin/bin/avr-gcc: No such file or directory
make[2]: *** [/cygdrive/c/Users/JUNJIE~1/WORKSP~1/FACHPR~1/erika/mk/ee_arch_rules.mk:201: obj/hardware/arduino/avr/cores/arduino/hooks.c.o] Error 127
make[2]: Leaving directory '/cygdrive/c/Users/JUNJIE~1/WORKSP~1/FACHPR~1/erika'
make[1]: *** [makefile:77: all] Error 2
make[1]: Leaving directory '/cygdrive/c/Users/JUNJIE~1/WORKSP~1/FACHPR~1/erika'
make: *** [makefile:92: /cygdrive/c/Users/JUNJIE~1/WORKSP~1/FACHPR~1/erika/lib] Error 2

15:51:38 Build Finished (took 4s.467ms)

It may be caused by the path problem. Can anyone give me some suggestions? Thanks in advance!

paolo.gai
Administrator
Posts: 875
Joined: Thu Dec 07, 2006 12:11 pm

Re: Build errors when using Erika3

Post by paolo.gai » Wed Mar 07, 2018 6:51 pm

The makefile cannot find the compiler...

You need to:
1) install the Arduino tools
2) link the compiler inside the properties, see
http://www.erika-enterprise.com/wiki/in ... figuration

I hope it helps...

PJ

Junjie
Newbie
Posts: 6
Joined: Wed Mar 07, 2018 4:00 pm

Re: Build errors when using Erika3

Post by Junjie » Thu Mar 08, 2018 9:39 am

Hi,

Thanks for your answer.
I have installed the Arduino (tried both 1.8.4 and 1.8.5), and it still doesn't work. (the same error message)

It seems that there is no file under "obj" folder, all the files haven't been copied from Arduino tool.

paolo.gai
Administrator
Posts: 875
Joined: Thu Dec 07, 2006 12:11 pm

Re: Build errors when using Erika3

Post by paolo.gai » Thu Mar 08, 2018 10:39 am

Can you please write:

- the directory where arduino is installed on your machine

- the value that you put in the RT-Druid properties (I mean the 4 values on the properties in Figure 12 of http://www.erika-enterprise.com/wiki/in ... figuration )

PJ

Junjie
Newbie
Posts: 6
Joined: Wed Mar 07, 2018 4:00 pm

Re: Build errors when using Erika3

Post by Junjie » Thu Mar 08, 2018 11:12 am

Hi,

I just find the reason...
I set the path of "AVR GCC Compiler" to the cygwin, which causes the problem. I should leave it as empty.
Now, it works~
Thanks a lot!

Post Reply