Search found 16 matches

by gina.torres
Tue Jun 26, 2012 5:00 pm
Forum: FLEX (closed)
Topic: Amazing Ball problems
Replies: 23
Views: 38175

Re: Amazing Ball problems

Hello Paolo, I have solved the issue finally, the problem was that FLEX Multibus Ethernet Module was wrong connected, i mean there was a problem with the hardware, now i can receive data from the Amazing Ball. The next step is continue with my real aim. Thanks for all your support. I really apprecia...
by gina.torres
Tue Jun 19, 2012 3:09 pm
Forum: FLEX (closed)
Topic: Amazing Ball problems
Replies: 23
Views: 38175

Re: Amazing Ball problems

Thanks again Paolo, I didn't know about that, i have tried pid_ctrl_udp_codegen.cos and as you said, it places the ball to the center but i cant send or receive data from the platform after doing exactly what you say in your steps. I am pretty sure that i am conecting well, the ethernet adapter in m...
by gina.torres
Wed May 30, 2012 12:37 pm
Forum: FLEX (closed)
Topic: Amazing Ball problems
Replies: 23
Views: 38175

Re: Amazing Ball problems

Thanks for your reply i haven't seen it before, i had solved that programming as you said with MPLAD IDE. Now that i have the correct program in my flex board i tested if my hardware is working properly but i found that it starts calibrating and the ball doesnt go to the center, it just stops, so th...
by gina.torres
Wed May 30, 2012 11:57 am
Forum: FLEX (closed)
Topic: Amazing Ball problems
Replies: 23
Views: 38175

Re: Amazing Ball problems

Hello,

I've solved this with Paolo's help but using MPLAB IDE, with MPLAB X was impossible to create a project for that prebuilt .cof ..

Thanks.

Gina Torres
by gina.torres
Wed May 30, 2012 11:56 am
Forum: FLEX (closed)
Topic: Problem saving pic30.cof in card with MPLAB IDE
Replies: 3
Views: 13463

Re: Problem saving pic30.cof in card with MPLAB IDE

Hello,

I've solved this with help of Paolo but using MPLAB IDE, with MPLAB X was impossible to create a project for that prebuilt .cof ..

Thanks.

Gina Torres
by gina.torres
Tue May 22, 2012 4:46 pm
Forum: FLEX (closed)
Topic: Amazing ball model
Replies: 17
Views: 31631

Amazing ball model

Hello all, In the rest of the replies of this forum, i have read that there are some articles where Amazing ball model was based to do the simple controller PI which is implemented, Could you give me please some articles where i could find the information?.I have found some but i would like to see w...
by gina.torres
Tue May 22, 2012 4:27 pm
Forum: FLEX (closed)
Topic: Problem saving pic30.cof in card with MPLAB IDE
Replies: 3
Views: 13463

Re: Problem saving pic30.cof in card with MPLAB IDE

Hello, I have the following problem: I try to create a project with MPLAB X, for the code generated by pid_ctrl_udp_codegen.cos and it can't create the project because pic30.cof is 29Mb, i realized about that because the other examples: The code generated by Led_sin.cos and pid_ctrl_usbudp_codegen.c...
by gina.torres
Mon May 21, 2012 10:15 am
Forum: FLEX (closed)
Topic: Amazing Ball problems
Replies: 23
Views: 38175

Re: Amazing Ball problems

Hello, Thanks for your reply. I have realized that i havent programmed my flex board correctly, i have been programming all time the code generated by pid_ctrl_usbudp_codegen.cos not the pid_ctrl_udp_codegen.cos , it was a mistake with MPLAB X. When i realized about that then i have this problem: I ...
by gina.torres
Tue May 15, 2012 12:50 pm
Forum: FLEX (closed)
Topic: Amazing Ball problems
Replies: 23
Views: 38175

Re: Amazing Ball problems

Hey All, I am having the same problems, i have done all what you have said: i'll programmed de generated program of "pid_ctrl_codegen_udp_tuning_square_circle.cos" on my Flex board, then i started "PCside_AmazingBall_UDP_PIDtuning.cos" i run the simulation and as i said in my last post but i dont kn...
by gina.torres
Wed May 09, 2012 12:48 pm
Forum: FLEX (closed)
Topic: Amazing Ball problems
Replies: 23
Views: 38175

Amazing Ball problems-UDP Communication

Hello, I have some problems testing the Amazing Ball Control System: An example of PID control and UDP communication, i have done all the first five steps of http://erika.tuxfamily.org /wiki/index.php?title=Amazing_Ball_Control_System:_An_example_of_PID_control_and_UDP_communication, and i have prog...
by gina.torres
Tue Apr 24, 2012 6:22 pm
Forum: FLEX (closed)
Topic: SCICOSLAB for UBUNTU
Replies: 2
Views: 12531

Re: SCICOSLAB for UBUNTU

Thanks for your reply!!.

Regards.

Gina
by gina.torres
Tue Apr 24, 2012 12:26 pm
Forum: ScicosLab and Scicos-FLEX code generation (closed)
Topic: Scicos Flex Code generator-Error. Help!!!
Replies: 3
Views: 15333

Re: Scicos Flex Code generator-Error. Help!!!

Sorry but, I dont know if i understood what you advice me, i am trying to modify the path but i dont find here the cygwin path, It appears like that: PATH: C:\Program Files\Microchip\MPLAB C30\bin;C:\Program Files\scicoslab-4.4.1\bin;C:\watcom-1.3\binnt;C:\watcom-1.3\binw;C:\Program Files\MiKTeX 2.8...
by gina.torres
Tue Apr 24, 2012 10:14 am
Forum: ScicosLab and Scicos-FLEX code generation (closed)
Topic: Scicos Flex Code generator-Error. Help!!!
Replies: 3
Views: 15333

Scicos Flex Code generator-Error. Help!!!

Hello, I have tried to generate code with the first example Led_Sin.cos but i have some errors as you can see in the picture attached, i have followed all the steps of installation and i don't know how to solve them. The unique thing that i have don different is that i installed Microsoft Visual C++...
by gina.torres
Tue Apr 24, 2012 10:09 am
Forum: ScicosLab and Scicos-FLEX code generation (closed)
Topic: Amazing ball - Scicos Flex Code generator
Replies: 19
Views: 33111

Re: Amazing ball - Scicos Flex Code generator

Hello, I have tried to generate code with the first example Led_Sin.cos but i have some errors as you can see in the picture attached (Step 3)., i have followed all the steps of installation and i don't know how to solve the problem . The unique thing that i have done different is that i installed M...
by gina.torres
Tue Apr 17, 2012 12:00 pm
Forum: ScicosLab and Scicos-FLEX code generation (closed)
Topic: Amazing ball - Scicos Flex Code generator
Replies: 19
Views: 33111

Re: Amazing ball - Scicos Flex Code generator

Hello

Can i use Scicoslab for Ubuntu for the amazing ball? It seems that the implementation of the Amazing ball is just for WIndows.

Thanks.

GIna