Search found 7 matches
- Mon Jun 05, 2017 12:50 pm
- Forum: ERIKA Enterprise and RT-Druid v2
- Topic: Tricore compilation
- Replies: 38
- Views: 199620
Re: Tricore compilation
Hi Thanks for the suggestion and instruction. I've done as suggested, undone all the changes that have been made (restoring rules_infineon_tc_generic.mk.bak to rules_infineon_tc_generic.mk and confirm the following: 12:44:11 **** Build of configuration Default for project Test **** "C:\\Users\\WinUs...
- Mon Jun 05, 2017 11:33 am
- Forum: ERIKA Enterprise and RT-Druid v2
- Topic: Tricore compilation
- Replies: 38
- Views: 199620
Re: Tricore compilation
Hi Ericco, thanks for your update Interrogating the version of make that I am using I get the following $ make --version GNU Make 3.81 Copyright (C) 2006 Free Software Foundation, Inc. This is free software; see the source for copying conditions. There is NO warranty; not even for MERCHANTABILITY or...
- Fri Jun 02, 2017 7:27 am
- Forum: ERIKA Enterprise and RT-Druid v2
- Topic: Tricore compilation
- Replies: 38
- Views: 199620
Re: Tricore compilation
Update: I've managed to successfully compile the example, but with a little messing about. After the Project Clean and Refresh stages, I copied the code.c file to the Debug folder and managed to get the project to finally compile: 07:15:20 **** Build of configuration Default for project Test **** "C...
- Thu Jun 01, 2017 3:53 pm
- Forum: ERIKA Enterprise and RT-Druid v2
- Topic: Tricore compilation
- Replies: 38
- Views: 199620
Re: Tricore compilation
Hi
Thanks for your update.
Yes, I cleaned and before the rebuild. Just to make sure, I've followed your steps exactly by adding the refresh in the also but still no further. Still, progress is being made.
Regards
Thanks for your update.
Yes, I cleaned and before the rebuild. Just to make sure, I've followed your steps exactly by adding the refresh in the also but still no further. Still, progress is being made.
Regards
- Thu Jun 01, 2017 1:23 pm
- Forum: ERIKA Enterprise and RT-Druid v2
- Topic: Tricore compilation
- Replies: 38
- Views: 199620
Re: Tricore compilation
Update: I've made some edits to the Hightec file: C:\HIGHTEC\toolchains\tricore\v4.9.1.0-infineon-1.1\tricore\include\tc27xa\IfxMtu_regdef.h The alternating lines from 136 - 198 inclusive and 205 - 251 inclusive have been commented out. I understand the use of a zero-length bit-field for alignment b...
- Thu Jun 01, 2017 12:33 pm
- Forum: ERIKA Enterprise and RT-Druid v2
- Topic: Tricore compilation
- Replies: 38
- Views: 199620
Re: Tricore compilation
Hi Thanks for your response. I did run the update, but whether or not you can see if it actually updated from the debug file I submitted is another question. I made the change that you suggested. However, the line in question was 211 and not 208 as may have been indicated in your post. The good news...
- Thu Jun 01, 2017 10:29 am
- Forum: ERIKA Enterprise and RT-Druid v2
- Topic: Tricore compilation
- Replies: 38
- Views: 199620
Re: Tricore compilation
It appears that I too am experiencing similar problems, even after the update. Platform is Windows 10 x64 with a TC275-based ShieldBuddy Downloaded and installed eeCygwin_1_7_9 Downloaded Erika and installed at C:\erika Updated the software as per Errico's post above: http://erika.tuxfamily.org/foru...