Search found 8 matches
- Tue Aug 23, 2011 1:12 pm
- Forum: ScicosLab and Scicos-FLEX code generation (closed)
- Topic: Amazing ball - Scicos Flex Code generator
- Replies: 19
- Views: 36982
Re: Amazing ball - Scicos Flex Code generator
Hi, Thanks Paolo.gai Got ICD3 and everything was working fine until today. But, suddenly i am not able to get any data from the board. I had opened the 'PCside_AmazingBall_UDP_Monitor.cos' file. I selected run from the simulate dropdown menu as always and then ScicosLab became unresponsive. I had to...
- Tue Jul 26, 2011 5:32 am
- Forum: ScicosLab and Scicos-FLEX code generation (closed)
- Topic: Amazing ball - Scicos Flex Code generator
- Replies: 19
- Views: 36982
Re: Amazing ball - Scicos Flex Code generator
Hi
No errors have been detected erikadds. I get a message that compilation is successful and a .cof file is generated (pic.cof).
I do not know how to burn this to the chip. Do i need ICD3 or is it possible to burn using the ethernet connection on the flex board?
Pleas Help
Regards
Vivek
No errors have been detected erikadds. I get a message that compilation is successful and a .cof file is generated (pic.cof).
I do not know how to burn this to the chip. Do i need ICD3 or is it possible to burn using the ethernet connection on the flex board?
Pleas Help
Regards
Vivek
- Thu Jul 21, 2011 11:10 am
- Forum: ScicosLab and Scicos-FLEX code generation (closed)
- Topic: Amazing ball - Scicos Flex Code generator
- Replies: 19
- Views: 36982
Re: Amazing ball - Scicos Flex Code generator
THANK YOU erikadds, it is working finally. :) I tried the first example from the wikipage(http://erika.tuxfamily.org/wiki/index.php?title=Tutorial:_Installing_scicoslab_and_generating_code_from_a_Scicos_diagram) i.e. led_sin.cos, but i cant find the .elf file as mentioned in step 7 under Generating ...
- Thu Jul 14, 2011 2:45 pm
- Forum: ScicosLab and Scicos-FLEX code generation (closed)
- Topic: Amazing ball - Scicos Flex Code generator
- Replies: 19
- Views: 36982
Re: Amazing ball - Scicos Flex Code generator
Hi, Its back to square one. I am getting the same error about failed dll link but for a different file - 'RollerGUI.dll'. Also there was no folder for Amazing Ball setup in the new Scicos pack i.e Scicos pack 10. So i copied the folder - 'FlexPIDTuning' from the CD, which has the dll file for Amazin...
- Thu Jul 14, 2011 2:25 pm
- Forum: ScicosLab and Scicos-FLEX code generation (closed)
- Topic: Amazing ball - Scicos Flex Code generator
- Replies: 19
- Views: 36982
Re: Amazing ball - Scicos Flex Code generator
Thank You very much Nicola.
I changed 'Programmi' to 'Program Files' and the installation is going on fine.
That was a really dumb mistake :)
Thanks again
Regards
Vivek
I changed 'Programmi' to 'Program Files' and the installation is going on fine.
That was a really dumb mistake :)
Thanks again
Regards
Vivek
- Thu Jul 14, 2011 11:39 am
- Forum: ScicosLab and Scicos-FLEX code generation (closed)
- Topic: Amazing ball - Scicos Flex Code generator
- Replies: 19
- Views: 36982
Re: Amazing ball - Scicos Flex Code generator
Hi, I followed all the instructions from the wiki page suggested by Nicola. When i try to install the Scicos pack 10 by executing installer.sce i get an error that the paths c:\Programmi\Microchip\MPLAB C30 and c:\Programmi\Microchip\MPLAB ASM30 Suite are not valid, but these folders exist. What mig...
- Tue Jul 12, 2011 12:33 pm
- Forum: ScicosLab and Scicos-FLEX code generation (closed)
- Topic: Amazing ball - Scicos Flex Code generator
- Replies: 19
- Views: 36982
Re: Amazing ball - Scicos Flex Code generator
Thanks Nicola
I am using EE 1.5.1 and Scicos pack 9, both from the CD accompanying the setup.
I will install the versions you suggested and post the results asap.
Regards
Vivek
I am using EE 1.5.1 and Scicos pack 9, both from the CD accompanying the setup.
I will install the versions you suggested and post the results asap.
Regards
Vivek
- Tue Jul 12, 2011 10:28 am
- Forum: ScicosLab and Scicos-FLEX code generation (closed)
- Topic: Amazing ball - Scicos Flex Code generator
- Replies: 19
- Views: 36982
Amazing ball - Scicos Flex Code generator
I have followed all the steps mentioned in the document 'flex_scicos_0_50.pdf' to install the scicos flex code generator. But I get the error - 'link failed for dll....' etc as can be seen in the attachment. Also I cannot find the - C:/Evidence/Bin folder or - the start menu folder or - an entry in ...